Verify CCU operation by running a Diagnostic Test or any cycle. Sarasota, FL "Best customer service experience I ever had." Christine G. Sd SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 Follow ApplianceAssistant on Twitter! About Appliance Repair Safety Legal Stuff Sponsor a Child => Future Hope Ministries Copyright Appliance Assistant, LLC. 2015 skip navigation Click to call Click to Chat http://ajdesignsoftware.com/error-code/error-code-f21-whirlpool-washer.php
Check the harness between the Steamer and the Steamer Electronic board. 3. Verify CCU is working by performing diagnostic test or any cycle. Press CANCEL and observe for 1 minute to ensure operation is correct. 2. Door switch/lock unit failure. 1. http://producthelp.whirlpool.com/Laundry/Washers/Washer_Product_Assistance/Error_codes_in_front_load_washers
Note: If this error occurs, the door will remain locked and the drain pump will run constantly even if 'cancel' is selected. Door switch/lock unit failure. 1. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Check the MCU by looking for operations of the drive motor. 7.
Select the 'cancel' function and wait 60 seconds. Replace heater. Plug in washer or reconnect power. 6. Whirlpool Duet Dryer Error Codes Other F# E# code Unplug the washer or disconnect the power for one minute and reconnect it again.
Bitte versuche es später erneut. Whirlpool Cabrio Error Code F02 Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed. Make sure that both valves at the water source(s) are turned on all the way. 2. Check the inlet valve and pressure switch for proper shut off and operation.
Unplug washer or disconnect power. 2. Whirlpool Duet Washer Error Codes F20 Unplug washer or disconnect power for two minutes. Check all hoses for possible leaks. 6. Measure door switch (door open = switch open small low voltage terminals).
Verify CCU operation by running a Diagnostic Test or any cycle. 3. Check dispenser motor for powered rotations. Whirlpool Washer Error Code F21 Unplug washer or disconnect power. 2. Whirlpool Top Load Washer Error Codes F7 Faults are motor and motor control related problems.
Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU this contact form Press CANCEL. Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. Potential Causes • Check wire harness connections between the Drive Motor/Tachometer and the Motor ControlUnit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the Drive Motor Whirlpool Washer Error Codes A10
See the repair guide to fix it yourself Water inlet valve assembly F/02 Takes a long time to drain Remove excess suds; the washer can't drain excessively sudsy water. Check Steamer for continuity (Abnormal =infi nity). 2. Check the electrical connections at the pump and make sure the pump is running. 4. http://ajdesignsoftware.com/error-code/error-code-f21-on-whirlpool-washer.php Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
The pressure switch is not tripped after 6 minutes. Whirlpool Washer Error Codes 5d Refer to the Continuity tests. Press HOLD TO START to continue the cycle, or press OFF/Pause to clear the display.
Unplug the washer for 5 minutes, restore power and see if the code clears. Verify CCU operation by running a Diagnostic test or any cycle. A: Whirlpool Duet products and parts can be purchased at big box stores, such as Best Buy, or via online retailers, such as Amazon. Whirlpool Duet Washer Error Codes F02 Check Door Lock/Switch Assembly for foreign objects Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Failure Join our VIP email list and
A power glitch may cause this error. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) Check/Clean Drain Pump Filter of foreign objects Check Drain Pump Check Pressure Switch Check CCU F/dL http://ajdesignsoftware.com/error-code/error-code-f20-whirlpool-washer.php LF - Long Fill - If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display.
Sr - Stuck Relay - The machine control board may have a bad relay and may need to be replaced. If this does not appear to be the case you may have mechanical friction causing drag when the inner washer drum is rotating. Replace motor controller. Check mains supply is in range (90V-132V).
Possible causes… 1. Check connections at control and at the latch switch and door switch. 2. Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen. Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check the electrical connections at the pump and make sure the pump is running.
If failure remains, disconnect power and replace control. Check the drain hose and make sure it is not plugged or kinked. 2. Press CANCEL. Press STOP/CANCEL to clear the display.
This error code may also be used if there is a disagreement between the motor and machine controllers on the state of the lid switch. Full Answer > Filed Under: Washers & Dryers You May Also Like Q: How do you buy coin-operated washers and dryers for a shared residence? Hinzufügen Möchtest du dieses Video später noch einmal ansehen? Check wire harness connections to the User Interface and the Central Control Unit. 3.
The machine control board may have a bad relay and may need to be replaced.