E061 STUDENT ID STUDENT ID must be student's 9-digit Social Security Number or FTE number. E2516 EIP LEVEL, PROGRAM CODES EIP Level transmitted does not match the segment information reported in current FTE collection. E004 SYSTEM CODE No course data have been transmitted. by Manage My Life May 18th, 2011 Comment 0 votes susannahva: I would suspect the motor control board is more likely faulty than the RPS sensor. http://ajdesignsoftware.com/error-code/error-code-start-process-failure-code-1603.php
E2174 BI-LIT LANGUAGE 2 Invalid code for BI-LIT LANGUAGE 2. E0100 SYSTEM OF RESIDENCY RESIDENT STATUS CODE = '7', SYSTEM OF RESIDENCY must = '801'. E167 STUDENT ID; GTID The STUDENT ID has been reported with more than one GTID this fiscal year. Trans 2357 Low clutch Solenoid is shorted to +12 Volts, current sensed while driver is off. http://www.valley-implement.com/error-codes.htm
E020 REPORT PERIOD REPORT PERIOD not valid, must equal '1' for Cycle 1, or '3' for Cycle 3. All personnel reported as active in CPI 2007-1 must be reported as either active or terminated in CPI 2007-2. ESOL must be equal or less than '2'. TMF 130 Aux 2nd Raise solenoid failed open or short circuit.
Hitch 1027 Not implemented Hitch 1028 Travel Range potentiometer value received from CAN data bus indicates failure condition. E2175 BI-LIT LANGUAGE 2 BI-LIT LANGUAGE 2 cannot be the same as for BI-LIT LANGUAGE 1 or BI-LIT LANGUAGE 3. Error Code Input Field(s) Error Message F T E F I N C P I S R E2507 SYSTEM ID The SYSTEM ID is not a valid system id in the Scania F 440 E1104 GTID; SCHOOL CODE NO LONGER VALID.
D131 GTID; STUDENT FIRST NAME (GUIDE) STUDENT FIRST NAME entered/uploaded is different than STUDENT FIRST NAME stored in GUIDE. Must be 'Y' or 'N'. Engine 3035 Oil Temperature Sensor -Signal Below Range Min. visit If you need assistance with your assigned numbers or need a new block of numbers, please submit a Helpdesk dticket.
E198 CREDIT IN LIEU OF COURSE CREDIT IN LIEU OF COURSE = 'Y' is only valid for EOC courses. Whirlpool Error Code F Trans 2363 The Odd Clutch is not calibrated Trans 2364 Even Clutch not calibrated Trans 2365 C1-2 Clutch not calibrated Trans 2366 C3-4 Clutch not calibrated Trans 2367 C5-6 Clutch not E014 GTID (No longer used 6/16- E0481) (GUIDE) GTID has been deactivated. TMF 160 PTO Clutch is Slipping Too Much TMF 162 Engine Stalled when the PTO was running.
Harold Jackson 110 192 visningar 3:39 Duet Sport Dryer 2008 Error code F 01 - Längd: 9:01. See Details More Products Kenmore 84422 3.4 cu. Db2 Error Code 440 The link is attached below. Secma F 440 If you were working on something in the car, such as EV mod, and had the car on while working on something, that would explain the codes.
E2005 FUND, FUNCTION, OBJECT No superintendent salary has been reported. this contact form E2040 BALANCE SHEET CODE Balance Sheet Account 0423 not Allowed in this Fund E2041 BALANCE SHEET CODE Balance Sheet Account 0711 not Allowed in this Fund ENG 2973 Intake Manifold 1 Pressure data invalid. Since you recorded all the codes, try clearing it and see if any come back. Abroad F 440
The year does not match when compared to the previous data. E126 PRE-K PROGRAM CODE, GRADE LEVEL If student's GRADE LEVEL is Pre-K, a PRE-K PROGRAM CODE is required. Trans 2343 Clutch Even solenoid open circuit or short to ground.C33 Trans 2344 Clutch C1-2 solenoid open circuit or short to ground. have a peek here See Data Discrepancy Report.
Circuit Board Medics 41 050 visningar 9:57 Whirlpool Duet Sport ht 5D/F21 Error Fix - Längd: 5:40. Whirlpool Error Code F 21 The unit was disconnected after the motor had started. 01-DC 178-2F-F Trasmission error. The problem was, these diagnostic codes were never really documented all that well.
Invalid for GRADE LEVEL 'PK' - '08'. ENG 2265 Electric Lift Pump for Engine Fuel Supply Voltage too high. E159 GAA; PRIMARY AREA GAA = 'Y', a PRIMARY AREA is required. Whirlpool Error Code F 02 E224 EL MONITOR BASIS Code missing or invalid for EL monitored student.
E142 ADDITIONAL COURSE TEACHER CODE ADDITIONAL COURSE TEACHER CODE cannot be all '0' (zeros). Trans 2056 5 volt internal reference voltage too high. This type of failure code is usually caused by a loose connection. Note: Disconnect the power cord before servicing your washer. If you do not feel confident repairing this problem yourself, then Check This Out E227 EL MONITOR BASIS EL MONITOR BASIS is required when EL MONITOR YEAR equals 1.
CCAE must be BLANK. Trans 2059 1) Switch inputs indicate shuttle lever is in both forward and neutral 2) Switch inputs indicate shuttle lever is in both reverse and neutral3) Switch inputs indicate shuttle lever Consult Student layout for valid codes. E082 SYSTEM OF RESIDENCY, RESIDENT STATUS CODE RESIDENT STATUS CODE = '1', SYSTEM OF RESIDENCY must = blank, zeros, null, or must be the same as the reporting SYSTEM code.
E195 CONTENT COMPLETER Must equal one of the following: 'P' - student had the opportunity to learn the entire course content and passed the course; 'F' - student had the opportunity It would appear that not all the codes generated are in the manual for each year. [/b]Click to expand... 1.